Pikmin 2 save file

Data about the Pikmin 2 save file format. The following info was taken from the US version of Pikmin 2 based on a .gci save taken from Dolphin. This data applies to all GameCube versions of the game, the only difference being the region code on the 4th byte of the file

To do: Figure out how to decrypt save files for the NPC version

The save file contains save data for each of the 3 save slot used in-game. The data of such a save slot starts with the 8 byte magic word string PlVa0003 and is 0xC000 bytes (49152 bytes in decimal) long. Directly after the string follows a byte which has the slot number of the save (0x00 for first slot, 0x01 for second, 0x02 for third). The last 4 bytes of the slot data contain the checksum calculated for the preceding slot data. The checksum is detailed in this section.

Addresses

Addresses of interest relative to the start of the save slot (i.e. the start of the magic word string):

Address	Size	Description
0x13	1 byte	When this byte is set to 0 the save file is considered new
0x14	4 bytes	Integer representing the day count as shown on the file select screen (might not be permanent, i.e. overwritten when you end a day normally.)
0x2C	4 bytes	Integer representing the Poko count as shown on the file select screen.
0x30	4 bytes	Integer representing the treasure count as shown on the file select screen. Usually the same as the amount of treasures as accessed on the Area Select Screen.
0x3C	4 bytes	Integer representing the time (in minutes) played on the save file as shown on the file select screen.
0x53	array of 2, 4 byte integers followed by a 1 byte bitmask	4 byte integer representing the count of enemies killed, followed by a 4 byte integer of Pikmin lost to the said enemy, followed by a 1 byte bitmask 0b1 representing that the enemy has been unlocked in the Piklopedia and 0b10 representing that the enemy has been viewed in the Piklopedia.
0x3E9	4 bytes	Actual day count the game registers, differing from what is displayed on the file select screen if only one of the two addresses is edited.
0x3ED	2 bytes	Bitmask for Exploration Kit items and their activity. The least significant bit represents the EK item with an internal ID of 0 When the bit is set to 1, the item is active. This activity does not reflect the treasure being collected.
0x3F1	21 length 4 byte array	Pikmin types that fall from the sky during entering and exiting a cave. Editing this value on a save file that is on the area select screen will result in the Pikmin falling from the sky upon entering an area. The Pikmin types are organized into groups of three, with the first integer representing a leaf Pikmin, the second a bud Pikmin, and the third a flower Pikmin. The Pikmin types in the array are ordered Blue, Red, Yellow, Purple, White, Bulbmin, and an unused Pikpik carrot.
0x479	21 length 4 byte array	Same as above but for Pikmin in the Onions and Ship. When either Bulbmin or Pikpik carrots are added the total number of Pikmin is increased however as they have no Onions there is no way to access them.
0x4CF	188 length 1 byte array	1 byte each represents the treasure as accessed on the area select screen. Treasures appear to follow their internal IDs for order. These are all the treasures not part of the Exploration Kit (nor The Key). Non-zero values mean collected. 02 means that the treasure will appear with "New" in the Piklopedia, while 06 means its old.
0x58D	13 length 1 byte array	Same as above, only for Exploration Kit treasures including The Key.
0x7D3	4 bytes	Integer count of how much Ultra-spicy spray the player has. (The game treats it as a signed integer but it appears to be displayed as an unsigned integer, but the game only shows the last three digits of the number)
0x7D7	4 bytes	Integer count of how much Ultra-bitter spray the player has. (The game treats it as a signed integer but it appears to be displayed as an unsigned integer, but the game only shows the last three digits of the number)
0x7E7	1 byte	Bitstream representing progress in Valley of Repose. If the least significant bit is set to 1 it plays the unlock fanfare next time the save is loaded. If the next bit is set to 1 then the fanfare won't play. To do: Figure out what the other bits control
0x7E8	1 byte	Used for the above ground treasure counter for the Valley of Repose on the map screen.
0x7E9	1 byte	Same as 0x7E7 but for the Awakening Wood.
0x7EA	1 byte	Used for the above ground treasure counter for the Awakening Wood on the map screen.
0x7EB	1 byte	Same as 0x7E7 but for the Perplexing Pool.
0x7EC	1 byte	Used for the above ground treasure counter for the Perplexing Pool on the map screen.
0x7ED	1 byte	Same as 0x7E7 but for the Wistful Wild.
0x7EE	1 byte	Used for the above ground treasure counter for the Wistful Wild on the map screen.
0x834	4 bytes	Actual Poko count the game registers, differing from what is displayed on the file select screen if only one of the two addresses is edited.

Checksum

The checksum of a save slot is calculated according to this method.

This Python script (requires Python >3.4) assists with calculating the checksum for the data in a save slot. Not recalculating and fixing the checksum results in the game detecting the modified save slot as being corrupted (but if you have any unmodified save slots, those will still work fine).

Very careful editing might allow you to fool the corruption detection without having to recalculate the value: Due to the checksum being an additive one, if you increase one value by 1 and decrease a different value by 1, the checksum should still remain valid.^[unsure]